Knowledge

Are Formic Acid and Acetic Acid the Same? Structure, Properties and Industrial Use

Oct 14, 2025 Leave a message

Short Answer: Two Different Carboxylic Acids

Formic acid and acetic acid are not the same substance. Both belong to the carboxylic acid family and both are traded as industrial commodity chemicals, but they differ in molecular size, acidity, freezing behaviour and the applications they serve. Formic acid (HCOOH, CAS 64-18-6) is the simplest carboxylic acid and carries a single carbon atom. Acetic acid (CH3COOH, CAS 64-19-7) carries two carbon atoms and is the acid of vinegar. Substituting one for the other in a process changes reaction stoichiometry, pH control, corrosion rates and the quality of the finished product.

Physical and Chemical Comparison

The table below lists the values normally published on a technical data sheet. They explain why the two acids are stored and dosed under different regimes.

Property Formic acid Acetic acid
Molecular formula HCOOH CH3COOH
CAS number 64-18-6 64-19-7
Molar mass 46.03 g/mol 60.05 g/mol
Density at 20 C about 1.22 g/cm3 about 1.05 g/cm3
Boiling point 100.8 C 118.1 C
Melting point 8.4 C 16.6 C
pKa in water 3.75 4.76

Formic acid is the stronger acid of the two, because the hydrogen atom bonded to the carboxyl carbon stabilises the anion formed on dissociation. Its lower molar mass also means that a given mass of formic acid delivers more acid equivalents than the same mass of acetic acid. Acetic acid freezes at 16.6 C, which is why glacial acetic acid must be kept above that temperature to avoid solidification inside drums, pumps and pipelines.

Where Formic Acid Is Used

Formic acid is applied as a preservative and acidifier in silage, where it suppresses undesirable fermentation and improves feed stability through the winter. In leather processing it is used in deliming and pickling. It acts as a reducing agent in textile dyeing and in several chemical syntheses, and it is employed in oil and gas well stimulation, in rubber coagulation and in the preparation of cleaning formulations. Industrial grades are supplied against the national standard for industrial formic acid, which sets assay, colour and residue requirements by grade.

Where Acetic Acid Is Used

Acetic acid is one of the highest-volume organic intermediates in the chemical industry. Its dominant outlet is vinyl acetate monomer, produced by reacting acetic acid with ethylene; vinyl acetate then feeds adhesives, paints and polymer dispersions. Acetic acid is also a raw material for purified terephthalic acid, cellulose acetate and acetic anhydride. As a solvent it appears in inks, coatings and purification steps, and diluted food grades are used as vinegar. Industrial acetic acid is traded against the national standard for glacial acetic acid, which grades the product by assay and by permanganate and water limits.

Handling, Packaging and Purchase Specifications

Both acids are corrosive to skin and eyes and must be handled with chemical-resistant gloves, goggles and, where mist can form, respiratory protection. Formic acid is supplied in 30 kg and 250 kg drums, in intermediate bulk containers of about 1000 litres, and in road tankers for full loads. Acetic acid follows the same packaging pattern, but because of its freezing point, insulated or heat-traced storage is required in cold climates. Purchase documents normally state the assay minimum, the water and iron content limits, the colour index and the requirement for a batch certificate of analysis. Buyers should confirm whether the grade is industrial, feed or food grade before shipment, because documentation requirements differ between them.

Frequently Asked Questions

Q: Are formic acid and acetic acid interchangeable in industrial processes?
A: No. Formic acid is a stronger acid and has a lower molar mass, so reaction stoichiometry, pH control and corrosion rates all change when one replaces the other.

Q: Which of the two is the stronger acid?
A: Formic acid, with a pKa of 3.75 in water, is stronger than acetic acid, which has a pKa of 4.76. The lower pKa value reflects greater dissociation.

Q: Why does acetic acid solidify in winter storage?
A: The melting point of acetic acid is 16.6 C, so below that temperature it freezes. Formic acid melts at 8.4 C and normally stays liquid in indoor storage.

Q: What packaging is standard for these two acids?
A: Both are packed in 30 kg and 250 kg drums and in 1000 litre intermediate bulk containers, with bulk road tankers used for large volume buyers.

Q: How should quotations from different suppliers be compared?
A: Compare assay, water content, colour index, iron and residue limits, packaging type, and whether the batch certificate of analysis is issued to the industrial, feed or food grade standard requested.

Q: Can formic acid be used as a silage additive?
A: Yes. It is widely applied as a silage preservative to control fermentation, and it is normally dosed as a diluted solution rather than as the concentrated acid.

Send Inquiry