Knowledge

Can DME (CAS 115-10-6) Be Used as Fuel? A Complete Guide

May 13, 2025 Leave a message

What Is Dimethyl Ether (DME)?

Dimethyl ether (DME, CAS 115-10-6, molecular formula C2H6O) is the simplest aliphatic ether. At ambient temperature it is a colorless, highly flammable gas with a faint ethereal odor, and it is handled as a liquid under moderate pressure or refrigeration. DME has physical properties close to those of liquefied petroleum gas (LPG), which is why the two are often blended or handled with similar equipment.

Can DME Be Used as Fuel?

Yes. DME is a proven clean-burning fuel with a high cetane number (about 55-60), which makes it an excellent substitute for diesel in compression-ignition engines with only minor fuel-system modifications. It burns without soot and with very low particulate, sulfur oxide and nitrogen oxide emissions, so it is regarded as one of the cleanest diesel alternatives. DME is also used as a cooking and heating fuel, blended with LPG (typically up to 20%) for domestic use, and as a propellant in aerosol products, replacing ozone-depleting CFCs. When produced from biomass, biogas or renewable methanol, DME is considered a renewable biofuel.

Key Properties

Property Value
CAS number 115-10-6
Molecular formula C2H6O / CH3-O-CH3
Molecular weight 46.07 g/mol
Boiling point -24.8 C
Flash point About -41 C (gas)
Liquid density About 0.67 g/cm3 at boiling point
Vapor density 1.59 (air = 1)
UN number 1033, Class 2.1 (flammable gas)

How Is DME Produced?

Commercially, DME is produced by catalytic dehydration of methanol over gamma-alumina or zeolite catalysts at elevated temperature and pressure. The methanol can come from natural gas, coal or biomass, and single-step processes that convert synthesis gas directly to DME have also been developed. China is the world's largest DME producer, with most capacity based on the coal-to-methanol route.

Safety and Handling

DME is an extremely flammable gas (GHS Flam. Gas 1, H220) and is stored and transported as a liquefied gas under pressure (UN 1033). Keep it away from heat, sparks and open flames; leaks can form explosive mixtures with air. Because DME can swell or soften natural rubber and some plastics, use compatible seals, gaskets and hoses (for example, materials rated for LPG service). Vapors are heavier than air and may accumulate in low-lying areas, so storage areas need good ventilation and gas detection.

Frequently Asked Questions

Q: Can DME be used as fuel?
Yes, as a diesel substitute, as a cooking and heating fuel, blended with LPG, and as an aerosol propellant.

Q: What purity is dimethyl ether normally supplied in?
Commercial DME is supplied in fuel, propellant and chemical grades, typically at 99% or 99.5% minimum purity, with methanol and water as the main impurities; the exact limits are stated on the certificate of analysis.

Q: What is the difference between fuel-grade and propellant-grade DME?
Fuel-grade DME may tolerate a small methanol content and is blended with LPG or used as a diesel substitute, while propellant-grade DME is purified to a higher quality (usually 99.5% or above) with very low moisture so that aerosol spray performance and can pressure remain consistent.

Q: What cetane number does DME have as a diesel substitute?
DME has a cetane number of about 55-60, higher than typical diesel fuel, which gives easy ignition, low noise and smooth combustion in compression-ignition engines with only minor fuel-system changes.

Q: How much DME can be blended with LPG?
DME is typically blended with LPG at up to about 20% for cooking and heating; because the two gases have similar properties, adapted LPG-type burners, cylinders and equipment can be used if seals and gaskets are DME-compatible.

Q: What is DME used for besides fuel?
DME is widely used as an aerosol propellant that replaced ozone-depleting CFCs, and it serves as a methylating agent and chemical feedstock, for example in the production of dimethyl sulfate and acetic acid.

Send Inquiry