Knowledge

Acrylic Acid CAS 79-10-7: Characteristics, Properties and Industrial Uses

Nov 24, 2025 Leave a message

What Is Acrylic Acid (CAS 79-10-7)?

Acrylic acid is the simplest unsaturated carboxylic acid, built from a vinyl group attached directly to a carboxyl group. Its molecular formula is C3H4O2 and its molar mass is about 72.06 g/mol. The monomer carries the CAS registry number 79-10-7 and is a clear, colorless liquid with a sharp, pungent odor. Industrially it is produced from propylene, which makes it one of the most important building blocks in the acrylic value chain.

Because the molecule contains both a polymerizable double bond and a reactive acid group, it can be converted into a very wide family of products, from water-soluble thickeners to superabsorbent polymers and acrylate esters.

Key Physical and Chemical Characteristics

Property Typical value
CAS number 79-10-7
Molecular formula C3H4O2 (CH2=CHCOOH)
Molar mass About 72.06 g/mol
Appearance Clear, colorless liquid
Odor Sharp, pungent, acrid
Density at 25 °C About 1.051 g/cm³
Boiling point About 141 °C at atmospheric pressure
Freezing point About 13 to 14 °C
Flash point About 50 °C
Solubility Miscible with water, alcohols, ether and chloroform
Stabilizer MEHQ, typically around 200 ppm
Transport classification UN 2218, class 8 corrosive with flammable subsidiary risk

The freezing point just above 13 °C is a practical detail for plant design: lines, pumps and storage tanks in cold climates need trace heating or insulation, because solidification can block transfer systems and is difficult to reverse without controlled warming.

Reactivity and Polymerization Behaviour

The carbon-carbon double bond makes acrylic acid a fast-reacting vinyl monomer. Polymerization yields polyacrylic acid, a water-soluble polymer widely used as a thickener, dispersant and scale inhibitor. Esterification with alcohols produces the acrylate esters, such as methyl acrylate, ethyl acrylate and butyl acrylate, which are the backbone monomers of acrylic emulsions for coatings, adhesives and textiles.

Highly exothermic: polymerization releases considerable heat, so reactors and storage tanks need cooling capacity and temperature monitoring.

Inhibitor dependent: commercial material always contains an effective inhibitor such as MEHQ, and its concentration must be checked regularly.

Oxygen sensitive: dissolved oxygen assists the inhibitor system, so headspace management matters in storage.

Water miscible: the monomer can be handled in aqueous as well as solvent-borne processes.

Corrosive: the acid attacks skin, eyes and many common metals, which dictates the choice of storage materials.

Acrylic acid should be stored in stainless steel, glass-lined or suitably lined vessels rather than in plain carbon steel, and it must be protected from uncontrolled heat sources, direct sunlight and contamination that could consume the inhibitor.

Industrial Applications Across the Acrylic Value Chain

Superabsorbent polymers. The largest single outlet is the production of crosslinked polyacrylic acid superabsorbents for hygiene products, where the polymer can absorb many times its own weight in water.

Coatings and paints. Acrylate esters made from acrylic acid form the binder of water-based architectural and industrial coatings, giving durability, colour retention and resistance to weathering.

Adhesives, sealants and textile finishes. Acrylic emulsions provide tack, flexibility and hand to pressure-sensitive adhesives, sealants, nonwovens and textile treatments.

Water treatment. Polyacrylic acid and its salts act as dispersants, antiscalants and flocculant aids in cooling water and industrial effluent systems.

Paper, leather and detergents. Acrylic derivatives serve as paper coatings and additives, leather auxiliaries, and builder or dispersant components in detergent formulations.

Thickeners and rheology modifiers. Alkali-swellable acrylic polymers are used to control viscosity in paints, cosmetics, drilling fluids and personal care gels.

Safety, Storage and Regulatory Classification

Acrylic acid is corrosive and can cause severe burns to skin, eyes and the respiratory tract, so full protective equipment is required during sampling, transfer and maintenance work. It is flammable, with a flash point near 50 °C, and it is classified for transport as UN 2218, class 8, with a flammable liquid subsidiary risk.

Storage areas should be cool, well ventilated and shielded from direct sunlight, with temperature monitoring and a documented inhibitor-check schedule. Because the monomer can polymerize violently if the inhibitor is depleted or if the material is contaminated or overheated, tanks are usually fitted with alarms and emergency quenching provisions. When purchasing, buyers should confirm that the material offered is the acrylic acid monomer under CAS 79-10-7 rather than a polymer or an ester, since the handling requirements and the price basis differ completely.

Frequently Asked Questions

Q: What is the CAS number of acrylic acid?
The CAS registry number of acrylic acid monomer is 79-10-7, and its molecular formula is C3H4O2.

Q: Is acrylic acid soluble in water?
Yes. Acrylic acid is miscible with water in all proportions, and it is also miscible with alcohols, ether and chloroform.

Q: Why does acrylic acid need an inhibitor?
Because it polymerizes rapidly and exothermically, an inhibitor such as MEHQ, typically around 200 ppm, is added to prevent uncontrolled polymerization during storage and transport.

Q: What is the boiling point and flash point of acrylic acid?
Acrylic acid boils at about 141 °C at atmospheric pressure and has a flash point of about 50 °C, so it is a flammable corrosive liquid.

Q: What is acrylic acid used for?
It is used to produce superabsorbent polymers, acrylate esters, acrylic emulsions for paints and adhesives, polyacrylic acid for water treatment, and many other acrylic derivatives.

Q: Is acrylic acid dangerous to handle?
Yes. It is corrosive and flammable, so chemical protective clothing, gloves and eye protection are required, and storage must be temperature controlled with inhibitor monitoring.

Q: How should acrylic acid be stored?
Store it in stainless steel or lined vessels in a cool, shaded, well-ventilated area, away from heat and ignition sources, with the inhibitor concentration checked on a fixed schedule.

Send Inquiry