Two Glycols, One Family, Different Behaviour
Monoethylene glycol (MEG) and diethylene glycol (DEG) are both produced from ethylene oxide and both belong to the glycol family, yet they behave very differently in a process line. MEG is the simplest glycol and the highest-volume industrial glycol worldwide. DEG is a dimer in which two ethylene glycol units are joined by an ether bond, so its molecule is larger, heavier and less volatile. Because of these structural differences the two products are not interchangeable, and choosing the wrong grade can alter reaction rates, finished-product hardness, freeze protection and regulatory compliance.
Chemical Identity and CAS Numbers
Monoethylene glycol (MEG): CAS 107-21-1, molecular formula C2H6O2, molecular weight 62.07 g/mol.
Diethylene glycol (DEG): CAS 111-46-6, molecular formula C4H10O3, molecular weight 106.12 g/mol.
Both are colourless, essentially odourless, water-miscible liquids supplied in ISO tanks, road tankers and 225 kg drums.
The additional ether linkage raises the molecular weight of DEG by about 71 percent compared with MEG. That single structural difference explains most of the property gaps described below: higher boiling point, higher viscosity, lower vapour pressure and greater solvent power for polar resins.
Physical Properties Compared
| Property | MEG | DEG |
|---|---|---|
| CAS number | 107-21-1 | 111-46-6 |
| Molecular formula | C2H6O2 | C4H10O3 |
| Molecular weight (g/mol) | 62.07 | 106.12 |
| Boiling point at 101.3 kPa | 197.3 °C | about 245 °C |
| Freezing point | about -13 °C | about -10.5 °C |
| Density at 20 °C | 1.113 g/cm3 | 1.118 g/cm3 |
| Viscosity at 20 °C | 16.1 mPa·s | 35.7 mPa·s |
The higher boiling point of DEG makes it the better choice where a solvent must survive elevated temperatures without evaporating, while the lower viscosity and lower cost per unit of freeze protection keep MEG dominant in coolant and de-icing duties.
Where Each Glycol Is Used
MEG is the principal raw material for PET resin used in beverage bottles, polyester fibre and packaging film.
MEG is the standard base fluid for automotive engine coolants and aircraft de-icing fluids.
MEG also serves as a hydrate inhibitor in natural gas pipelines.
DEG is used as a high-boiling solvent in chemical synthesis and as a plasticiser that increases the flexibility of polymers.
DEG appears in unsaturated polyester and alkyd resin manufacture, and in gas dehydration where a higher boiling point is required.
DEG is also found in textile lubricants, heat-transfer fluids, polyurethane formulations and some brake fluid packages.
One non-negotiable rule applies: DEG is toxic when ingested and must never enter food, beverage, pharmaceutical or cosmetic products. Its use is confined to clearly labelled industrial processes with suitable engineering controls.
Quality Control, Storage and Safe Handling
Buyers normally specify glycols by purity, water content, colour and acidity. Purity and water in glycols are commonly measured using the test methods described in ASTM E202, while industrial ethylene glycol grades are covered by specifications such as GB/T 4649. Typical purchases state purity at 99.5 percent or higher for industrial grade and 99.9 percent or higher for fibre and resin grade, with water held in the low hundreds of parts per million. Exact grade limits always follow the edition of the standard named on the order.
Both glycols are hygroscopic and should be stored in closed, nitrogen-blanketed or desiccated tanks to protect the low water specification. Mild steel or stainless steel tanks with suitable gaskets are typical, and heating coils should be sized to keep viscosity in a pumpable range without overheating. MEG and DEG have low vapour pressure at ambient conditions, so exposure risk is mainly through skin contact, mists and aerosols. Splash goggles, chemical-resistant gloves and adequate ventilation are standard practice, and spills should be absorbed and recovered rather than washed into drains.
Frequently Asked Questions
Q: What is the main difference between MEG and DEG?
MEG is the simplest glycol with formula C2H6O2 and CAS 107-21-1, while DEG is a larger molecule with formula C4H10O3 and CAS 111-46-6, which gives it a higher boiling point and higher viscosity.
Q: Is DEG more volatile than MEG?
No. DEG is less volatile than MEG because of its higher molecular weight and its boiling point of about 245 °C against 197.3 °C for MEG.
Q: What is MEG mainly used for?
MEG is used chiefly for PET resin production, polyester fibre, automotive antifreeze and coolants, and gas hydrate inhibition.
Q: What is DEG used for?
DEG serves as a high-boiling solvent, a plasticiser, an unsaturated polyester and alkyd resin intermediate, a gas dehydration agent and a heat-transfer fluid.
Q: Why is DEG restricted in food and pharmaceutical work?
DEG is toxic if ingested and has caused serious poisoning incidents, so it is excluded from food, beverage, pharmaceutical and cosmetic applications and handled only in controlled industrial processes.
Q: Can MEG and DEG be stored in the same equipment?
Dedicated lines are preferred. If equipment is shared, it must be drained and cleaned so that DEG carry-over does not contaminate a fibre-grade MEG specification.
